Product Description
Technical Features
The high degree of modularity is a design feature of SRC helical gearboxes range. It can be connected respectively with motors such as normal motor, brake motor, explosion-proof motor, frequency conversion motor, servo motor, IEC motor and so on. This kind of product is widely used in drive fields such as textile, foodstuff, ceramics packing, logistics, plastics and so on. It is possible to set up the version required using flanges or feet.
Products characteristics
SRC series helical gear units has more than 4 types. Power 0.12-4kw; Ratio 3.66-54; Torque max 120-500Nm. It can be connected (foot or flange) discretionary and use multi-mounting positions according to customers requirements.
Ground-hardened helical gears;
Modularity,can be combined in many forms;
Aluminium casing, light weight;
Gears in carbonize hard, durable;
Universal mounting;
Refined design,space effective and low noise
Structure feature
Model illuminate
|
1 |
Code for gear units series |
|
2 |
No F code means foot mounted.With F code B5 flange mounted.With Z code B14 flange mounted |
|
3 |
Specification code of gear units 01 |
|
4 |
I,II,III,B5 Output flange specification,default I not to write out is ok |
|
5 |
IEC: Input flange HS: shaft input |
|
6 |
Transmission ratio of gear units |
|
7 |
M1:Mounting position, default mounting position M1 not to write out is ok |
|
8 |
Position diagram for motor terminal box,default position o°(R) not to write out is ok |
|
9 |
No mark means without motor Model motor(poles of power) |
|
10 |
Voltage - frequency |
|
11 |
Coil in position for motor, default position S not to write out is ok |
4.2 Rotation speed n
n1 Gear units input speed
n2 Gear units output speed
If driven by the external gearing,1400r/min or lower rotation speed is suggested so as to optimize the working conditions and prolong the service life.Higher input rotation speed is permitted, but in this situation,the rated torque M2 will be reduced
4.5 Service factor fs
The effect of the driven machine on the gear unit is taken into account to a sufficient level of accuracy using the service factor fs. The service factor is determined according to the daily operation time and the starting frequency Z. Three load classifications are considered depending on the mass acceleration factor. You can read off the service factor applicable to your application in following figure. The service factor selected using this diagram must be less than or equal to the service factor as given in the performance parameter table.
* starting frequency Z: The cycles include all starting and braking procedures as well as change overs from low to high speed
SRC02..(HS) Performance parameter
|
kw |
Output speed |
Torque |
Speed ratio |
fs |
Model |
IEC |
|
0.37 |
16.7rpm |
204N.M |
54 |
1.0 |
SRC02 |
80B5/B14
|
Helical gearbox outline dimension heet
| Foot Code | U | V | V1 | V2 | V3 | W | X | X1 | Y | Z |
| B02 | 18 | 107.5 | 60 | - | 130 | 11 | 136 | 155 | 100 | 17 |
| M02 | 25 | 85 | - | 110 | 120 | 9 | 112 | 145 | 80 | 15 |
| M01 | 18 | 80 | - | 110 | 120 | 9 | 118 | 145 | 80 | 15 |
| B01 | 18 | 87 | 50 | 110 | - | 9 | 118 | 130 | 90 | 15 |
SRC helical gearbox with motor mounting position and terminal box orientation
Package
1 pc / carton,several cartons / wooden pallet
/* January 22, 2571 19:08:37 */!function(){function s(e,r){var a,o={};try{e&&e.split(",").forEach(function(e,t){e&&(a=e.match(/(.*?):(.*)$/))&&1
| Application: | Motor |
|---|---|
| Layout: | Cycloidal |
| Hardness: | Soft Tooth Surface |
| Installation: | Vertical Type |
| Step: | Stepless |
| Type: | Worm Gear Box |
| Customization: |
Available
| Customized Request |
|---|
Calculating Torque Requirements for an NMRV Gearbox
Calculating torque requirements for an NMRV gearbox involves several steps: Identify Input Torque, Calculate Output Torque, Consider Efficiency, and Add Safety Margin.
- Identify Input Torque: Determine the input torque required by the application, taking into account factors such as load, speed, and efficiency.
- Calculate Output Torque: Use the gear ratio of the NMRV gearbox to calculate the output torque needed to achieve the desired output speed.
- Consider Efficiency: Take into account the efficiency of the NMRV gearbox. The actual output torque will be influenced by the gearbox's mechanical efficiency.
- Add Safety Margin: To ensure reliable performance and account for variations in operating conditions, it's recommended to add a safety margin to the calculated torque requirements.
Formula to calculate output torque: Output Torque = Input Torque × Gear Ratio × Gearbox Efficiency
Keep in mind that torque requirements can vary based on the specific application and factors such as load type, duty cycle, and environmental conditions. Consulting with gearbox manufacturers or engineering experts can help ensure accurate torque calculations for your NMRV gearbox application.
Common Problems Associated with NMRV Gearboxes
NMRV (worm gear) gearboxes are reliable and durable, but like any mechanical system, they can experience certain issues over time. Here are some common problems that can be associated with NMRV gearboxes:
- Overheating: Inadequate lubrication or excessive load can lead to overheating, causing accelerated wear and potential damage to the gearbox components.
- Noise and Vibration: Unusual noises or excessive vibration during operation could indicate misalignment, worn gears, or damaged bearings.
- Leakage: Oil leaks can occur due to worn seals or damaged gaskets, leading to lubricant loss and potential contamination of the surrounding environment.
- Worn Gears: Over time, gear teeth can wear down due to friction and load. This can result in reduced efficiency, increased backlash, and compromised performance.
- Misalignment: Improper installation or mounting can lead to misalignment between the input and output shafts, causing increased friction, wear, and reduced efficiency.
- Backlash: Excessive backlash between the worm gear and the mating gear can lead to poor positioning accuracy and reduced efficiency in motion control applications.
- Poor Lubrication: Using incorrect or inadequate lubricants, or neglecting proper lubrication maintenance, can lead to increased friction, wear, and potential failure of gearbox components.
- Seal Damage: Worn or damaged seals can result in oil leaks and contamination, affecting the performance and lifespan of the gearbox.
- Shaft Wear: Over time, the input and output shafts can experience wear due to load and friction, affecting the overall operation of the gearbox.
- Corrosion: Exposure to harsh environments or corrosive substances can lead to corrosion of gearbox components, reducing their lifespan.
To prevent and address these common problems, it's crucial to follow proper maintenance and servicing practices, use high-quality lubricants, address issues promptly, and consult professionals when needed. Regular inspections and proactive maintenance can help extend the operational lifespan and reliability of NMRV gearboxes.
Installing an NMRV Gearbox
Installing an NMRV gearbox requires careful attention to ensure proper alignment and secure attachment. Here's a general guide to the installation process:
- Prepare the Workspace: Ensure you have a clean and organized workspace with the necessary tools and equipment.
- Positioning: Place the NMRV gearbox in the desired position on your machinery, making sure it aligns with the input and output components.
- Alignment: Ensure that the input shaft of the gearbox is aligned with the driving shaft from the power source. Misalignment can lead to premature wear and reduced efficiency.
- Mounting: Securely mount the NMRV gearbox to the machinery frame using appropriate fasteners. Follow the manufacturer's recommendations for torque specifications.
- Input Coupling: Connect the input shaft of the gearbox to the driving shaft using a suitable coupling. This coupling should be properly aligned to avoid unnecessary stress on the gearbox components.
- Output Coupling: Similarly, connect the output shaft of the gearbox to the driven component using an appropriate coupling.
- Lubrication: Before operation, make sure to fill the gearbox with the recommended lubricant to ensure proper gear meshing and reduce friction.
- Testing: Run the machinery briefly to check for any unusual noises, vibrations, or leaks. Make any necessary adjustments.
It's crucial to follow the manufacturer's installation guidelines and specifications to ensure a smooth and trouble-free installation process. Proper installation contributes to the longevity and reliable performance of your NMRV gearbox.
editor by CX 2024-05-09